Famco Chimney Liner & Rebuild Nationwide

Famco Chimney Liner & Rebuild in Astoria: What to Know First

Famco chimney liner and rebuild work in Astoria typically runs $1,800 to $4,900 depending on whether we’re replacing a liner, rebuilding the crown, or pulling down and relaying the full stack. We’re an independent Famco service provider, not a factory shop, and most liner replacements are completed in one day with a written price before anything starts. The camera comes down the flue on every job, and you leave with photos whether you book the repair or not. Call (516) 301-1549 to schedule an inspection.

Call (516) 301-1549

This page is for Famco owners in Astoria whose liner has cracked, whose mortar joints are failing, or whose chimney has started pulling away from the house. If you’ve been told you need work and want to see the evidence yourself, you’re in the right place.

Key takeaways:

• Famco liners and caps appear most often in Astoria’s brick rowhouses built between 1910 and 1935
• We write the price before work starts, always, no exceptions
• Every job includes a camera-scan inspection and a documented photo record
• 365-Day Done Right Promise on all liner and rebuild work

How Famco Products Fail - and How We Fix Them

Famco builds solid stainless liners and caps, but in Astoria’s wet winters and salt-adjacent air, specific failure patterns show up repeatedly. Here’s what we see in the field.

• Famco flexible liner seam separation at the first offset. On 316L flexible liners, the spiral lock seam near the first bend from the flue collar is the weak point. Astoria’s houses settle, the footing shifts, and the liner flexes at that seam until a hairline gap opens. We see it in roughly one out of every four Famco installs over 12 years old. The fix is usually a full liner replacement, not a patch. Patching a seam on a creosote-bearing liner is a temporary measure that fails the Level 2 standard.
• Famco rigid liner section corrosion at the mortar line. On older Famco rigid stainless sections, water seeping through a cracked crown or failed mortar joint sits at the section collar and starts pitting the steel. By the time you see rust streaks on the chimney face, the liner wall has usually lost measurable thickness. We replace the section and address the water entry point in the same visit.
• Famco multi-flue cap corrosion on the underside. The underside of Famco multi-flue caps traps condensation in Astoria’s humid summer months. The stainless looks fine from the street, but the welds underneath fail first. We’ve replaced caps that looked brand new up top and were Swiss cheese below. A camera scan catches this before it becomes a water-in-the-firebox problem.
• Famco oval-to-round transition cracking in tight flues. Astoria’s older homes often have narrow flue openings that require an oval liner compressed to fit a round flue collar. The transition point on Famco liners is a known stress zone. Hairline cracks there let flue gas into the chase, and carbon monoxide follows. This is a replacement scenario, not a repair one, and it’s one of the reasons we always scan before quoting.
• Famco cap screen plugging on wood-burning setups. On homes that burn wood regularly, the fine mesh on Famco cap screens loads with creosote faster than coarser aftermarket screens. A plugged screen chokes the draft and pushes smoke back into the living space. We clean the screen or swap it for a coarser option when the liner and appliance allow. It’s a $60 to $120 fix that saves a $900 rebuild.

Our Famco Chimney Liner & Rebuild Process

Every Famco job in Astoria follows the same sequence, whether it’s a liner replacement or a full rebuild. Nothing gets skipped, and you see the evidence at each step.

1. 1
   Camera-scan inspection. We run a Level 2 camera down the flue and log the exact liner condition. You see the footage on the spot. Clause 4 of the Haven Standard requires a photo record on every visit, and it’s been that way since 2009.
2. 2
   Written scope and price. Before any work starts, you get a written scope, written price, and written warranty. Not a verbal estimate. Not a rough number. A document.
3. 3
   Parts decision. If the liner is a Famco and we’re replacing it, we’ll quote OEM where the warranty matters and a quality DuraFlex or HeatShield alternative where the flue configuration calls for something Famco doesn’t make in that size. You see the trade-off in writing.
4. 4
   The work itself. Liner drop or removal, crown work if needed, smoke chamber parging where the rebuild demands it, cap replacement, and proper termination. All work is done to the NFPA 211 Level 2 standard.
5. 5
   Post-work camera verification. We scan the new liner after installation and show you the footage. You get the before photos, the after photos, and the written warranty before we leave.
6. 6
   The 365-Day Done Right Promise. If it’s not done right, we make it right. Stamped on every job under the Haven Standard.

Before

After

What Famco Chimney Liner & Rebuild Costs in Astoria

You should see the numbers before you call. Here’s what Famco chimney liner and rebuild work costs in Astoria as of 2026.

• Famco liner replacement (flexible, single flue): $1,800 to $2,900
• Famco liner replacement (rigid, two-story): $2,400 to $3,800
• Crown rebuild (poured, with expansion joint): $700 to $1,400
• Partial rebuild (above roofline, 5 to 8 courses): $1,500 to $2,800
• Full chimney rebuild (from roofline up): $3,500 to $4,900
• Famco cap replacement (single flue): $220 to $480
• Smoke chamber parging: $600 to $1,100

What moves the price is the flue height, the liner diameter your appliance requires, the condition of the crown and smoke chamber, and how much scaffolding the Astoria roofline demands. We price all of it in writing before anything starts. Call (516) 301-1549 for a free estimate with camera evidence.

Why Astoria Homeowners Call Level Two Chimney Astoria for Famco Work

Most of our Famco calls in Astoria come from someone who was told they needed a new liner but never saw the inside of the flue. That’s where we start. The camera doesn’t guess. Neither do we. If the liner is fine, we say so and send you the photos. If it’s not, you see exactly what we see, and you get a written price before any work begins.

Every tech on a Famco job is background-checked, uniformed, and carries their license number on the page. We answer the phone 24/7 with a live person. And because we work with DuraFlex, HeatShield, Gelco, and Copperfield materials through the same buying network, we’re not married to one brand. If a DuraFlex liner fits the flue better than a Famco OEM, we’ll tell you and show you the price difference in writing.

Corrine Halstead has been running chimney work across Queens for the better part of two decades, much of it in the older brick rowhouses along Steinway Street and the blocks around it. She learned the diagnostic side at LaGuardia Community College, and she’s known in Astoria for writing down the price before she starts and leaving a copy of the inspection photos whether the customer books or not.

FAQs